Expert Answers about Truck Bed Step

• Where Do I Install a TracRac SR On My 2020 Ford F150 5-1/2 Foot Bed?
• I have a couple troubleshooting steps to suggest. The first thing I noticed was that the part number for this question is the TracRac SR Sliding Truck Bed Ladder Rack # TH43002XT-501. This model of the SR is customized for the 2020 Ford F-150 6-1/2 foot bed. The part needed for the 2020 Ford F-150 5-1/2 foot bed is part # TH43002XT-508. If you have the # TH43002XT-501, it will not fit your truck. Another thing to consider is if the stake pocket tabs have been removed from the stakes on...
  view full answer...


• Truck-Bed Camper Troubleshooting For Tie-Down / Step Space Issue
• The TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear Item # TLR3510 is competing for the same space as the step so unfortunately there isn't a work around for this tie down. Instead you could replace the steps that bolt onto the wall of the camper like the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 3 Steps - 375lbs - Black Bracket Item # TLA7833. There are a few different options depending on the entry height of your camper which you can see in the chart I've attached....
  view full answer...


• 5th Wheel Trailer Pulls Nose High Are Spacers Available to Level with My 2011 2500 Dodge Ram Diesel
• The first thing I would do in your situation is take the truck and trailer to your RV dealer and have them check out your setup. Typically 5th wheel trailers are set up to tow a bit pin high to allow for more weight transfer to the rear most axle or axles on the trailer. If possible, you can adjust the trailer pin box closer to the underside of the trailer loft, or reduce the height of your fifth-wheel hitch head in the bed of your truck. Be aware that adjusting the trailer too close to...
  view full answer...


• How to Lower Nose of Fifth Wheel Trailer When Hitch is as Low as Possible
• Typically there are several different sets of holes that can be used to secure the pin box of the trailer to the trailer frame. You should be able to remove the hardware holding the pin box and then reinstall it higher on the trailer frame to allow the trailer to sit level. Otherwise you would need to go with a shorter height fifth wheel hitch or lift the suspension of the trailer. You will want there to be at least 6 inches between the bed rail of the truck and the trailer overhang.
  view full answer...


• Brake Controller Stoplight Switch Circuit of 2001 GMC Sierra 2500 Not Working
• This is a pretty common issue for GM trucks around the age of yours. It's the third brake light fuse of your 2001 GMC Sierra 2500 that is blown. When it goes the brake controller activation circuit stops working as well. You can test this really easily by pressing the brake and seeing if the third brake lights up on cab above truck bed.
  view full answer...


• Blank Display and PL Error Code on a Tekonsha Trailer Brake Controller, 1996 Chevy 3500 Diesel
• The PL error code on your brake controller indicates that power to the unit has been interrupted. I would check several things to determine what the problem is. Some of this may seem redundant since you have done a lot of troubleshooting already. Since you first encountered the problem when you connected the gooseneck to the in-bed connector, I would check the grounds for both the truck side and trailer side to make sure there is no corrosion and that they are attached properly. You can...
  view full answer...


• Trailer Sways with the Blue Ox Sway Pro Weight Distribution System # BXW1000
• Your truck, trailer and weight distribution system all appear to be compatible with each other, If you are still experiencing sway after installing the Blue Ox Sway Pro Weight Distribution System, # BXW1000, there are a few things we can look at. The first thing that I would look at is the tongue weight of the trailer. The tongue weight of the trailer, when it is loaded and ready to tow, should be 10 to 15 percent of the gross trailer weight. If the tongue weight is too light or too heavy,...
  view full answer...


• Trailer Left Turn Signal Stopped Working on a 2001 Ford F-250/F-350 Super Duty with Tow Package
• The relays and fuses that are included with the Ford Replacement OEM Tow Package Wiring Harness, # 118243, do not affect the turn signal functions but there could still be relays/fuses related to the tow package wiring that do affect the turn signals. What you can do is to check with the vehicle owners manual for all of the fuses and relays related to the tow package. You can then check those to determine if there is a problem and replace as needed. Otherwise, checking the wiring would...
  view full answer...


• Brake Controller in a 2001 Dodge Ram Pickup does not Recognize the Trailer
• All of the symptoms you are describing lead me to believe there is a ground problem somewhere, even on the trailer. A weak ground connection can show up with some trucks and not others, we have seen it before. The first step I would take is to inspect all of the ground connections on your truck and your trailer. Inspect the grounds for the trailer connectors and the grounds at the brake assemblies for the brake magnets. Even if the grounds look good, I remove and clean them. If they look...
  view full answer...


• Why Doesn't the Curt Hitch # C15318 Fit onto My 2001 Dodge Ram Pickup?
• Sorry to hear about your fitment issue! From the looks of your order with us, you bought the Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2" # C15318. This model is confirmed to fit some 2001 Dodge Ram Pickup 2500 models. It will not fit other submodels of Ram pickups for that year. Also, the hitch does not fit Sport models with dual exhaust. It also is only compatible with 6-1/2 foot beds with the standard or step bumper. If you have a 2001 Ram that fits the compatibility criteria,...
  view full answer...


• Troubleshooting Furrion Vision S Camera System Not Getting Camera Signal On Monitor
• I am sorry to hear that you are having issues getting your Furrion Vision S camera to display on the monitor. Since you mentioned that you already tried moving the monitor closer but that didn't help, I recommend double checking that there is no appliances on in your trailer that could be causing interference. If that is not the case then I recommend checking that the antenna on the is installed all the way, and is pointing vertically. Lastly try to unpair the camera and repair it to...
  view full answer...


• How to Correct Fifth Wheel Fishtailing on Lifted Trailer
• Tall/lifted trucks are not ideal for towing since they can lead to an out-of-level (nose high) condition on the trailer, which in turn can lead to issues with sway. Even though you have taken steps to get the trailer level again (the axle over-under kit, which gets you a few inches of additional height, and the pin box adjustment) you then still have a related problem: a higher center of gravity for the entire towing system, truck and trailer. The higher the trailer's center of gravity...
  view full answer...


• Right Side Trailer Lights Do Not Work on Trailer Towed by a 2014 Nissan Titan
• To determine if the trailer light problem is with the truck wiring or the trailer the first step is to test the truck side trailer connector. Using a circuit tester such as # PTW2993 test the pins on the connector while someone goes through the various light functions. If everything checks out ok on the truck side, then that indicates a problem on the trailer side. If the trailer connector has some functions that are not working the problem is on the truck. Use the truck owner's manual...
  view full answer...


• Reese 16K 5th Wheel Trailer Hitch Jaws Will Not Lock Around King Pin
• I am a little confused because a slider hitch would be in the truck bed not on the 5th wheel trailer. It sounds like maybe you have a telescoping pin box on the trailer. Regardless, when a 5th wheel hitch doesn't lock around the trailer king pin there are some things you can check on the hitch. First, make sure that the jaws of the hitch open and close freely. If they do not or it is difficult to open and close the jaws then the hitch may need to be lubricated. Also, following the hitching...
  view full answer...


• Running Lights on 2 Trailers Not Working Towed By a 2003 Ford Ranger
• Since the issue is happening on both trailers, it seems unlikely that the trailers are the problem. So, the first step is to isolate the problem by testing the truck side trailer connector with no trailer connected. You will need a circuit tester, # PTW2993 if you do not have one, to test the wiring. Have someone sit in the truck and go through the lighting functions while you test the connector with the circuit tester. If the running light circuit (located next to the ground pin) is not...
  view full answer...


• How to Properly Seat Self Adjusting Brakes
• While the Electric Trailer Brake Kit # AKEBRK-35-SA are self adjusting, they do still require an initial bedding of the brakes (breaking in/seating the brakes) to work properly. I have listed the steps to do this below. 1: Pick an open stretch of road that will allow you to stop multiple times 2: Adjust brake control power to MAX 3: Speed up to 40mph, then use the manual override on the brake control to reduce speed to 20mph 4: Repeat 12-15 times, allowing time for brakes to cool in...
  view full answer...


• Brake Controller Not Activating Trailer Brakes when Stepping on Brake Pedal in International Truck
• When a brake controller does not activate the trailer brakes when you step on the brake pedal that indicates a problem on the red wire going into the brake controller. A lot of big trucks like your International will not have a brake switch wire that you can use if the truck has air brakes. In that scenario the brake light only signal has to be obtained elsewhere such as at a third brake light or a fuse. If the truck does have a brake switch wire you can use, then it will only have power...
  view full answer...


• Trailer Brake Lights Do Not Work when Headlights Are On
• It sounds as if there is a weak ground connection somewhere on the trailer. Ground issues normally show up when there is more load on a system. Your situation is a perfect example of that. With the running lights on already drawing power, stepping on the brakes adds even more draw on the system. First, to isolate the issue, disconnect the trailer from the truck. Then use a circuit tester, like # PTW2993 if you do not already have one, to test the connector on the truck. Have someone run...
  view full answer...


• Finding Cause of Brake Lamp on Challenger 5th Wheel that Illuminates when Running Lights are On
• The first step is to determine if the problem is on the vehicle or the trailer. Use a circuit tester like part # PTW2992 on the pins of the trailer connector on your truck. Have a helper activate each lighting function as you test the pins on the connector to ensure that the correct pins are getting power while the correct function is activated. The Trailer Wiring help article I've linked you to shows which pin should carry which function. If the running lights are switched on, you shouldn't...
  view full answer...


• Troubleshooting P-3 Brake Controller Installation on a 2001 Chevrolet 2500HD Cab and Chassis Model
• The issue may be that your 2001 Chevrolet 2500HD cab and chassis model has the plug for the brake controller, but the electric brake and power lead wires are not run for it. If you are not getting power to your factory brake controller plug, you will need to connect the blue electric brake wire and red power lead wire under your vehicle hood. First, you will remove the bracket in the corner that is closest to the driver to access the accessory fuse block. Once you reveal the fuse...
  view full answer...